Your new thermostat should come with the o-ring gasket, but if it didn't, be sure to buy and install it before you install the new thermostat. This can cause the engine to overheat and create serious engine troubles. Remove 2 thermostat housing retaining bolts and remove the housing. Regular Cab SuperCab 4x2 4x4 4x2 4x4 4. Normally it is the upstream sensors sensor 1 that go first.
Remove the upper radiator hose at the thermostat housing. It is designed to block the flow of coolant to the radiator until the engine has warmed up. They see the harshest conditions. The engine cylinders are numbered 1 , 2 , 3 from front to rear on the passenger side of the engine and 4 , 5 , 6 fr … om front to rear on the drivers side of the engine. Most orders are shipped the same day. Your truck can overheat for many different reasons, and it's a problem that should be addressed as soon as possible. Remove the thermostat and O-ring from the lower intake manifold.
Also, it is common that the imrc will get clogged up with… On the coil pack , the row of 3 nearest the passenger side is numbered 1 , 2 , 3 from front to rear and the row of 3 nearest the drivers side is numbered 5 , 6 , 4 from front to rear The engine cylinders are numbered 1 , 2 , 3 from front to rear on the passenger side of the engine and 4 , 5 , 6 from front to rear…. A new thermostat replacement for Ford F150 effectively eliminates these problems and makes sure your truck maintains proper engine temperatures when you need it to most. Regular Cab SuperCab SuperCrew 4x2 4x4 4x2 4x4 4x2 4x4 4. Twist the radiator cap counterclockwise to pull off the radiator. Tighten the cap onto the radiator. Install a new O-ring, on the thermostat and position the thermostat in the lower intake manifold.
Disconnect the negative battery cable. Regular Cab SuperCab SuperCrew 4x2 4x4 4x2 4x4 4x2 4x4 4. Sometimes it will take 15 minutes or take a few hours it depends on your luck… It is located on the backside of the intake manifold. The thermostat can be found by following the top radiator hose to where it goes into the block. Drain and recycle the engine coolant.
Start the engine and allow it to reach normal operating temperature while checking for coolant leaks. A faulty thermostat will stick and cause the coolant to back up in the radiator. Disconnect the negative battery cable. Contrary to what aftermarket coolant manufacturers say, there is no such thing as a universal coolant. It's much cheaper t … o buy the right coolant the first time around. Step 5 - Replace the thermostat Now you can reach your thermostat to replace it. Drain about 1 gallon of coolant from the radiator Remove this housing Note how thermostat is installed Clean both surfaces Replace thermostat and gasket Re-install housing Re-fill coolant … slowly to prevent an air lock Start engine and look for leaks Run engine to normal operating temperature with heater on Re-check coolant level On the coil pack , the row of 3 nearest the passenger side is numbered 1 , 2 , 3 from front to rear and the row of 3 nearest the drivers side is numbered 5 , 6 , 4 from front to rear.
Maximum Loaded Trailer Weight lbs. Our online parts catalog uses real-time inventory, so you can be assured the parts you buy are in stock at the time of ordering. You have to remove the upper intake manifold to get to it. Clean the O-ring sealing surfaces. You could easily be looking below 10-12mpg. Clean… 2002 Ford F-150 headlight bulb lamp replacement: Purchase the correct replacement headlight bulb s first, before disassembling the vehicle.
Remove 2 thermostat housing retaining bolts and remove the housing. Just replace it when performing a cooling system service. Clean the O-ring sealing surfaces. Your thermostat reduces engine wear, deposits, and emissions. You don't have to let all of it out.
An overheating transmission can be the first warning sign to a disastrous outcome if not properly diagnosed and fixed. Then consult your owner's manual for the headlight bulb lamp replacement procedure. Place the thermostat housing on the lower intake manifold and install 2 retaining bolts. You can also use a clean drain pan here so that you can reuse your coolant after you're done. Step 4 - Remove the thermostat housing Grab your socket wrench and sockets again to remove the two bolts holding the thermostat housing to the intake manifold. Sensor 1 is the upstream sensor near the frame, between the block and the cat and Sensor 2 is near the Y-pipe downstream of the cat.
The thermostat sits between the engine and the radiator of your Ford F-150. Remove 2 thermostat housing retaining bolts and remove the housing. Remove the thermostat and O-ring from the lower intake manifold. This part is also sometimes called Ford F150 Thermostats. Connect the negative battery cable. Call toll free to order or place your order online via our secure checkout system.