Always come to a complete stop before shifting into and out of R Reverse. Slide the control to the right to restore the window controls. Keywords: 2006, factory, ford, auto, repair, manual, service, shop, official, oem, focus, cd-rom, taurus, sho, escort, mustang, freestyle, crown, victoria, thunderbird, focus, 500, galaxy, mondeo, probe, fusion, edge, fiesta, how, troubleshoot, trouble, shoot, diagram, replacement, problem, wiring, dtc, obd-ii, obdii, obd2, code, 4. Remove the bulb socket from the lamp assembly by turning counterclockwise. Tachometer if equipped : Indicates the engine speed in revolutions per minute. Regardless of whether it has a bumpy suspension, doesn't shift into gear, needs a new oxygen sensor, needs an inspection, has parts coming loose, is vibrating during driving, leaks oil from the engine, emits smoke from the tailpipe, needs electrical work, does not turn over, backfires through the exhaust, makes a loud thumping noise, or has some other car problem that requires service, the RepairSurge software will help you solve your car problem.
For normal operation, move control up two positions. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. The belt will click as it retracts to indicate it is in the automatic locking mode. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation.
Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. N Neutral With the gearshift lever in N Neutral , the vehicle can be started and is free to roll. If it enters the red section, the engine is overheating. They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. If the engine idle speed does not slow down automatically, have the vehicle checked. Your new, unprogrammed key is now programmed. Allow the belt to retract. If the indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Pull the bulb straight out of the socket.
The sensor also turns off the airbag when the passenger seat is empty to prevent unnecessary replacement of the airbag s after a collision. Locate the vertical adjuster on each headlamp, then use a 7 mm Allen wrench or a Phillips screwdriver to adjust the headlamp. Note: In the illustrations, lightning bolts are used to designate the assisting boosting battery. Hundreds of illustrations show the management and individual stages of work. The remote entry system activates the illuminated entry feature. Regardless of whether it has a bumpy suspension, doesn't shift into gear, needs a new oxygen sensor, needs an inspection, has parts coming loose, is vibrating during driving, leaks oil from the engine, emits smoke from the tailpipe, needs electrical work, does not turn over, backfires through the exhaust, makes a loud thumping noise, or has some other car problem that requires service, the RepairSurge software will help you solve your car problem. Increasing speed while using speed control There are two ways to set a higher speed:.
Flash to pass Pull toward you slightly to activate and release to deactivate. The site administration does not bear any responsibility for illegal actions, and any damage incurred by the copyright holders. Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses. Step 3 must be completed within 50 seconds after the safety belt warning light turns off. Do not attempt to push-start your vehicle. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
Make sure the tires are cool, meaning they are not hot from driving even a mile. Mixing Motorcraft Specialty Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection. Automatic transaxle fluid dipstick if equipped 8. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Color schemes of electrical equipment. Ford may change the contents without notice and without incurring obligation. Pull headlamp control towards you to turn foglamps on. All of Chilton's online content for the 2006 Ford Focus is updated monthly, so you'll have the most recent information on hand for any Do-It-Yourself project. Ford or Mercury vehicles customers call 1—800—241—3673;. Fasten your safety belt as normal, and the belt will slide to the front of the steel bar along the bottom of the door.