Always verify all light bulb sizes, bulb voltage usage and bulb wattage before applying any information found here to your 2008 Chevrolet Suburban. Press down the release tab on the electrical connector and slide the plug straight off the base of the old bulb. This was done on a 2007 but should work the same for 2008, 2009 and maybe even newer. Remove the vertically mounted bolt on the top of the headlight housing by turning it counter clockwise with the 10mm socket and ratcheting wrench. Get trustworthy advice provided by helpful staff when you purchase headlights for Chevy Suburban at your local AutoZone. Not the most user friendly design either. Insert the screw on the bottom of the headlight assembly and replace the wheel well cover.
Detailed pictures of the preceding steps are included near the bottom of this page. There is this retaining spring holding the bulb in place and they do not tell you how to remove it. Headlights grow dimmer by up to 20% over time and eventually burn out - for this reason, we recommend changing your headlights in pairs. Changing both headlight bulbs on your Suburban 1500 at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. Disconnect the electrical quick connect. . AutoZone features a wide variety of headlights from some of the industry's top brands, so you can bank on premium quality and long-lasting durability when you order from us.
Re-insert the four air box screws and tighten them in the clockwise direction with the screwdriver. Tighten the two bracket bolts in the clockwise direction with the 10mm socket and ratcheting wrench. Slide the headlight housing back in to place and line up the two bolt holes on the top with their corresponding holes in the engine bay frame. Even in large vehicles like a 2008 Chevrolet Suburban, this repair is pretty simple. Re-insert the 10mm bolt to secure the windshield washer fluid bottle in place and tighten it in the clockwise direction. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. Set the bolt aside in a safe place.
If it is difficult … to remove, you may have to loosen the screws that hold the spoiler. Push the power plug on to the base of the new high beam bulb until it clicks securely in to place. There are two pins on the outer edge that go into grommet holes. Replace the wiring connector to the back of the bulb. See sources and related links below for replacement bulb information. Learn how to perform this repair so you can be prepared when the issue arises.
Once the connector is freed from the tail light assembly you can remove the bulb by pressing inward on the tabs at base of the bulb, one on each side. Replace the assembly as it was originally in. Headlights are meant to help you see and be seen at night and in inclement weather such as fog, rain, sleet and snow. Pull back the carpeting directly behind the tail light that needs to be changed. Just unscrew the 4 nuts from behind the trim and very carefully pop out the assembly.
For more, check out my other. The entire tail light assembly will rotate laterally about 45 degrees or so to the left for a left tail light and the right for the right side. Adding More Information If you would like to help the Modified Life community by adding any missing information or adding a new light bulb size information to our resource, please feel free to or post it at the bottom of this page. The outer bolt is mounted vertically and the inner bolt is mounted horizontally. Replace the bulb socket in reverse to the way you took it off. In order to get to the tail light, and turn signal bulbs you have to remove the assembly. Installation is reverse of removal.
Loosen the rear headlight bolt by turning it counter clockwise with the 10mm socket and ratcheting wrench. Put on the wing nuts and reconnect the harness. Push the electrical connector on to the base of the new low beam bulb until it clicks securely in to place. It should work onsimilar suburban designs 2000-2006, but I have not verified that. In some Chevrolets, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb and vise versa. With the two upper headlight bolts removed and the housing pulled forward a bit, you should be able to access the old high beam bulb. It's easy for others to see you coming in your Chevy Suburban, but you need to make sure you see others as well.
You may want to consider replacing both left and right at the same time in order to keep brightness and color equal optional. Remove the two bolt screws pointed out in the video. Test the new bulbs by turning on the parking lights, switching on the headlights, flashing the high beams and activating the hazard signals. Use a magnetic tip screwdriver if possib … le. Recently I replaced the bulbs in the headlights on my Mazda one finally burned out.
The oil from your skin can cause the glass to shatter. From there, you turn the bulb ballasts counterclockwise and pull them out, and you can either replace the bulbs at that point, or the whole headlight assembly if necessary. Remove the … se to expose the screws that hold the light in place. Headlights grow dimmer by up to 20% over time and eventually burn out - for this reason, we recommend changing your headlights in pairs. You can complete this task in as little as 15 minutes and in the comfort of your own driveway. Our Chevrolet Suburban light bulb guides allow you to easily replace light bulbs, replace headlight bulb, change a broken lightbulb, install a hid headlight conversion or install led light bulbs instead of spending countless hours trying to figure out which light bulb sizes in your 2008 Chevrolet Suburban.